First Alert PIR725 Gebrauchs- und Pflegehandbuch PDF herunterladen

USER’S MANUAL

MOTION SENSING

HANDS-FREE SOCKET

Cat. PIR 725

120VAC, 60 Hz, 100W Max.

M08-0222-004 11/14

IMPORTANT! PLEASE READ CAREFULLY AND SAVE.

This user’s manual contains important information about your Motion

Sensing Hands Free Socket’s operation. If you are installing this unit for use

by others, you must leave this manual—or a copy of it—with the end user.

mounted lower than 8 feet,

it will not “see” quite as far.

Do not mount the Motion

Sensing Hands Free Socket

higher than

10 feet from the floor.

LIMITATIONS OF MOTION SENSING

HANDS FREE SOCKET

This Motion Sensing Hands Free Socket:

• Is for indoor use only.

• Requires AC power to function properly. If AC power to the unit is cut off,

it will not work.

• Is NOT intended to serve as a safety or security device. It is designed for

convenience only.

This Motion Sensing Hands Free Socket will not work properly if:

• The socket to which it is connected is defective or if the bulb is

burned out.

• It is used with anything other than a ceiling-mounted, bare bulb light

socket.

Although the Motion Sensing Hands Free Socket

detects changes in temperature, it is not intended to

be used as a heat and/or fire detector. Consult NFPA

Standard 72, National Fire Alarm Code, for residential

smoke detection and fire protection guidelines.

Although this Motion Sensing Hands Free Socket detects

motion 360º, the unit responds more effectively at each 180º

point. (See figure right.) The 180º points are marked on the

top of the unit by arrows. After installing the unit, rotate it

until either arrow faces the general direction of the path peo-

ple will most likely cross.

In hot temperature environments over 90 degrees Fahrenheit, use a maximum

75W bulb.

This device is designed for INDOOR USE ONLY. Do not allow it to get wet.

Infrared cannot penetrate glass or plastic. Do not use

in a glass-enclosed light or shaded lamp.

USE ONLY WITH A CEILING-MOUNTED, BARE BULB

LIGHT SOCKET.

INSTALLING THE MOTION SENSOR

Never touch the Motion Sensing Hands Free Socket, bulb, or socket with

wet hands or when the floor is damp or wet.

Turn the light OFF when installing the unit.

1. Turn the power to the light socket you have

chosen OFF.

2. Remove the light bulb from the socket.

3. Screw the Motion Sensing Hands Free Socket

directly into the empty socket.

4. Screw the light bulb into the Motion Sensing Hands

Free Socket.

5. Turn the power ON. After several seconds, the light

will turn on. The light will remain on for approximately

4 minutes after you leave the area. (A built-in delay of

several seconds allows the light bulb to cool before the

motion sensor is able to detect motion again.)

The unit is now ready to operate automatically.

It is possible that the light may turn off while you are within the sensing

area. For example, you may have been standing still.

TROUBLESHOOTING

CONSUMER AFFAIRS 1-800-323-9005

The lights do not turn on 1. Bulb is burned out

when movement is detected 2. Power switch is OFF

3. Rotate directional alignment arrows

4. Bulb wattage may be too low

The lights turn on and off 1. Bulb is more than 100 watts

repeatedly 2. Motion Sensing Hands Free Socket must be mounted

at least 12 inches from any wall or door

3. Heat sources in target area

The light stays on 1. Bulb is more than 100 watts

continuously 2. Motion Sensing Hands Free Socket must be mounted

at least 12 inches from any wall or door

3. Heat sources in target area

Temporary power failure–turn light off and on again

Sensing range is reduced 1. Very warm temperatures can temporarily reduce the

sensing range of the Motion Sensing Hands Free

Socket

NOTE: If the Motion Sensing Hands Free Socket is less than 12 inches away from a

door or wall, reduce bulb wattage or apply masking or electrical tape over a portion of

the sensor lens in direct line with the wall or door to reduce reflection.

CLEANING AND REPAIRING

To clean the Motion Sensing Hands Free Socket:

1. Turn the light OFF.

2. Remove the Motion Sensing Hands Free Socket and bulb from

the light socket.

3. Wipe the unit with a soft cloth. Do not use harsh cleaners of any kind.

Do not allow the unit to get wet or be submerged in water.

Never touch the Motion Sensing Hands Free Socket, bulb, or socket with

wet hands or when the floor is damp or wet.

Always turn the light OFF when cleaning.

Do not attempt to repair your Motion Sensing Hands Free Socket yourself. If

it does not appear to be working properly and it is still under warranty, return

it to BRK Brands, Inc. If the unit is no longer under warranty, please discard it

and replace it with a new unit.

LIMITED WARRANTY

Coverage: BRK Brands, Inc. warrants its enclosed Motion Sensing Hands Free

Socket to be free from defects in materials and workmanship under normal use for

a period of three years from the date of purchase. During the first year after the date

of purchase, BRK Brands, Inc. will replace any defective Motion Sensing Hands Free

Socket without charge. During the next two years, BRK Brands, Inc. will replace any

defective Motion Sensing Hands Free Socket at a charge to you not to exceed BRK

Brands, Inc.’s cost. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail

purchase and is not transferable. Keep the original sales receipt. Proof of purchase is

required to obtain warranty performance. Dealers, service centers, or retail stores sell-

ing this product do not have the right to alter, modify or any way change the terms and

conditions of this warranty. In new construction, if your Motion Sensing Hands Free

Sockets were installed by a contractor, this warranty is valid for the homeowner at the

time of installation from the date of original installation and is not transferable.

This warranty does not cover normal wear of parts or damage resulting from any of

the following: negligent use or misuse of the product, use on improper voltage or

current, or use contrary to the operating instructions, disassembly, repair or alteration

by anyone other than BRK Brands, Inc. Further, the warranty does not cover acts of

God, such as fire, flood, hurricanes and tornadoes.

BRK Brands, Inc. shall not be liable for any incidental or consequential damages

caused by the breach of any express or implied warranty. Except to the extent prohib-

ited by applicable law, any implied warranty of merchantability or fitness for a partic-

ular purpose is limited in duration for 3 years. Some states, provinces, or jurisdictions

do not allow the exclusion or limitation of incidental or consequential damages or lim-

itations on how long an implied warranty lasts, so the above limitations or exclusions

may not apply to you. This warranty gives you specific legal rights, and you may also

have other rights that vary from state to state, or province to province.

Service: Units that are under warranty and require service, please contact the

Consumer Affairs Department (800) 323-9005, Mon-Fri, 7:30am-5:00pm CST

First Alert

is a registered trademark of The First Alert Trust.

Made in China

Distributed by BRK Brands, Inc., Aurora, IL 60504-8122

Consumer Affairs: Monday-Friday, 7:30am-5pm (Central Time):

(800) 323-9005. Internet: www.firstalert.com

The First Alert

Motion Sensing Hands Free Socket senses your approach

and automatically turns on the light. The light remains on as long as the

motion sensor detects activity in the room, turning the light off approximately

4 minutes after you leave the area.

The Motion Sensing Hands Free Socket is ideal for walk-in closets, laundry

room, utility room or basement. It offers the convenience of automatic lighting

where you might otherwise have to search for a wall switch or pull string.

Use the Motion Sensing Hands Free Socket in any area or room that is

equipped with a ceiling-mounted, bare bulb light socket.

The motion sensor is not designed for use with an enclosed or shaded

bulb of any kind. Use only with a ceiling-mounted, bare bulb light socket.

DO NOT use with halogen bulbs.

SPECIAL FEATURES

The Motion Sensing Hands Free Socket:

• Detects motion in all directions–approximately 360º.

• Senses activity at a distance of 12 feet (when mounted at a height of 8 feet

above the floor).

• Turns the light off automatically approximately 4 minutes after movement in

the area stops.

• Works in full daylight, in darkness, and at any light level in between.

• Uses a standard incandescent bulb up to 100 watts, a compact

fluorescent bulb up to 50 watts, or a LED bulb up to 1,600 lumens (16 watts).

WHERE TO MOUNT THE UNIT

Be sure the socket selected is at least 12 inches from any wall or door.

Choose

any ceiling-mounted, bare bulb light socket. Mounted at a height of

8 feet, the Motion Sensing Hands Free Socket will sense the approach of a

person five feet tall at a distance of 12 feet. If the Motion Sensing Hands Free

Socket is mounted higher than 8 feet, it will “see” somewhat farther. If it is

US Patent D320,595

M08-0222-004 11/14

Model

PIR 725

1 2

USER’S MANUAL 1
MANUAL DEL USARIO 2

Inhaltsverzeichnis

Seite 1 - USER’S MANUAL

USER’S MANUALMOTION SENSING HANDS-FREE SOCKETCat. PIR 725120VAC, 60 Hz, 100W Max.M08-0222-004 11/14IMPORTANT! PLEASE READ CAREFULLY AND SAVE.This us

Seite 2 - MANUAL DEL USARIO

120V CA, 60 Hz, 100W Max.M08-0222-004 11/14¡IMPORTANTE! LEA CUIDADOSAMENTE ESTAS INSTRUCCIONES Y CONSÉRVELAS.Este manual del usuario contiene import

Kommentare zu diesen Handbüchern

Keine Kommentare

First Alert PIR725 Gebrauchs- und Pflegehandbuch

Stöbern Sie online oder laden Sie Gebrauchs- und Pflegehandbuch nach Bewegungsmelder First Alert PIR725 herunter. First Alert PIR725 Use and Care Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern